                   .:                     :,                                          
,:::::::: ::`      :::                   :::                                          
,:::::::: ::`      :::                   :::                                          
.,,:::,,, ::`.:,   ... .. .:,     .:. ..`... ..`   ..   .:,    .. ::  .::,     .:,`   
   ,::    :::::::  ::, :::::::  `:::::::.,:: :::  ::: .::::::  ::::: ::::::  .::::::  
   ,::    :::::::: ::, :::::::: ::::::::.,:: :::  ::: :::,:::, ::::: ::::::, :::::::: 
   ,::    :::  ::: ::, :::  :::`::.  :::.,::  ::,`::`:::   ::: :::  `::,`   :::   ::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  :::::: ::::::::: ::`   :::::: ::::::::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  .::::: ::::::::: ::`    ::::::::::::::: 
   ,::    ::.  ::: ::, ::`  ::: ::: `:::.,::   ::::  :::`  ,,, ::`  .::  :::.::.  ,,, 
   ,::    ::.  ::: ::, ::`  ::: ::::::::.,::   ::::   :::::::` ::`   ::::::: :::::::. 
   ,::    ::.  ::: ::, ::`  :::  :::::::`,::    ::.    :::::`  ::`   ::::::   :::::.  
                                ::,  ,::                               ``             
                                ::::::::                                              
                                 ::::::                                               
                                  `,,`


https://www.thingiverse.com/thing:2556993
Spider Prowler (28mm) by SebTheis is licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license.
http://creativecommons.org/licenses/by-nc-sa/3.0/

# Summary

Hi !

Here is a printable proxy for space zombies spider;

- legs : print 4 + 4 mirrored
- arms and upper arms : 2 + 2 mirrored 
- pincers : 2 + 2 mirrored 
- leg support : print 6 times

*************************
edit 29/09 : 
- arm half V2 (previous version missed the engraving on the side)
- uploaded weapons parts

edit 01/10/2017 :
all parts uploaded and ready for print except body

edit 08/10/2017 : final version of body_V2 with increased clearance for legs
******************************

Note : I am not the designer of the model (designed by Christian Groß), I just slice it in printable parts, correct many meshes errors, and add/modify details, scale...


== Please consider sending tips if you like my printable models ==

Copyright infringement is not intended. Parts are created freehand in 3d modeling software, no copyrighted product had been scanned or copied in any way. These models are for personal use as proxies and should never be sold. If it causes copyright issues, i will remove it.

# Print Settings

Printer: prusa i3 custon
Rafts: No
Supports: Yes
Resolution: 0.1 or less
Infill: 20%

Notes: 
Some parts need a lot of supports (cockpit, control panel).
all the parts that have been cut in halves don't need supports.
It is not very long to print as parts are thin

# Post-Printing

![Alt text](https://cdn.thingiverse.com/assets/9e/fa/91/bb/ff/20170928_191422.jpg)
Bottom weapon : check !

![Alt text](https://cdn.thingiverse.com/assets/22/44/e8/4f/c5/20170929_185755.jpg)
Set of 4 legs printing. Everything goes fine

![Alt text](https://cdn.thingiverse.com/assets/91/81/4a/5f/42/1506704392686-1950401834.jpg)
The leg supports were hard to fit in the body. I'll upload a new body with increased clearance.

![Alt text](https://cdn.thingiverse.com/assets/74/58/fe/11/19/20170930_162622.jpg)
Leg and weapon assembly on body : check. Seat, pedals and control panel printed ok

![Alt text](https://cdn.thingiverse.com/assets/22/be/c9/9c/da/20170930_224825.jpg)
Cockpit and top spine printed as one part : check. Now I need a necron pilot ^^